在線客服
微信客服
點擊圖片查看原圖
[VIP第3年] 指數:3
通過認證 
咨詢電話
021-80392549
|
店鋪基本資料信息
|
|||||||||||||||||||||||
GSM-20H10提供±210V / ±1.0*** / 22W的四象限操作。在***象限和第三象限，它們作為電源運行，為負載供電。在第二和第四象限，它們作為負載使用，在內部耗散功率。而電壓值、電流值和電阻值可以在電源或負載操作期間進行量測，其準確度高達0.012%并且分辨率可達1μV/10pA/10μΩ。
采樣的速度上，GSM-20H10支持***高50k點/每秒的采樣速度，可更精準地針對待測物的特性進行分析。透過4.3寸的大尺寸屏幕，更可以將所有的量測設定、參數與結果都完整的顯示在屏幕上。支持SDM (Source Delay Measure)功能，可設定信號產生變化時，延后進行采樣，避免穩定前的信號被擷取進去造成誤判。內建四種程序輸出模式(Linear, Log, SRC-MEM, Custom)，***多可支持2500個點的程序變化輸出。
在設備保護上，GSM-20H10提供了OVP/OTP保護模式；在OVP的設計上，使用者可自定義OVP的范圍，而OTP的保護則可有效防止在測試過程中因溫度偏移造成的錯誤。在接口部分，本產品支持標準的SCPI指令，提供RS-232 , USBTMC , LAN, GPIB (選配)等接口，滿足用戶不同的接口需求。
產品規格
|
Maximum Range |
Voltage |
±210V |
||||||||
|
Current |
±1.0*** |
|||||||||
|
Power |
22W |
|||||||||
|
Voltage Resolution |
1μV |
|||||||||
|
Current Resolution |
10pA |
|||||||||
|
Source |
DC Voltage |
Output Voltage |
±21V/ ±1.0***, ±210V/±105 mA |
|||||||
|
Current Limit |
Min. 0.1% of range |
|||||||||
|
Programming Resolution |
1μV, ±200.000mV range |
|||||||||
|
10μV, ±2.00000V range |
||||||||||
|
100μV, ±20.0000V range |
||||||||||
|
1mV, ±200.000V range |
||||||||||
|
Programming Accuracy 1 |
±(0.02%+600μV), ±200.000mV range |
|||||||||
|
±(0.02%+600μV), ±2.00000V range |
||||||||||
|
±(0.02%+2.4mV), ±20.0000V range |
||||||||||
|
±(0.02%+24mV), ±200.000V range |
||||||||||
|
Load Regulation |
0.01% of range + 100μV |
|||||||||
|
Line Regulation |
0.01% of range |
|||||||||
|
Overshoot |
<0.1% typical (full scale step, resistive load,10mA range) |
|||||||||
|
Recovery Time (1000%Load Change) |
<250μs (within 0.1% plus load regulation errors, 1A and 100mA compliance.) |
|||||||||
|
Ripple and Noise |
4mV rms(20Hz~ 1MHz) 10mVpp(20Hz~ 1MHz) |
|||||||||
|
Temperature Coefficient |
±(0.15 × accuracy specification)/°C |
|||||||||
|
DC Current |
Output Current |
±1.0*** /±21V, ±105 mA /±210V |
||||||||
|
Voltage Limit |
Min. 0.1% of range |
|||||||||
|
Programmed Source Resolution |
10pA, ±1.00000μA range |
|||||||||
|
100pA, ±10.0000μA range |
||||||||||
|
1nA, ±100.000μA range |
||||||||||
|
10nA, ±1.00000mA range |
||||||||||
|
100nA, ±10.00000mA range |
||||||||||
|
1μA, ±100.000mA range |
||||||||||
|
10μA, ±1.00000A range |
||||||||||
|
Programmed Source Accuracy 1 |
±(0.035%+600pA), ±1.00000μA range |
|||||||||
|
±(0.033%+2nA), ±10.0000μA range |
||||||||||
|
±(0.031%+20nA), ±100.000μA range |
||||||||||
|
±(0.034%+200nA), ±1.00000mA range |
||||||||||
|
±(0.045%+2μA), ±10.00000mA range |
||||||||||
|
±(0.066%+20μA), ±100.000mA range |
||||||||||
|
±(0.27%+900μA), ±1.00000A range |
||||||||||
|
Load Regulation |
0 0.01% of range + 100pA |
|||||||||
|
Line Regulation |
0.01% of range |
|||||||||
|
Overshoot |
<0.1% typical (1mA step, RL = 10kΩ, 20V range). |
|||||||||
|
Temperature Coefficient |
±(0.15 × accuracy specification)/°C |
|||||||||
|
General |
Output Settling Time2 |
100μs typical Time |
||||||||
|
Output Rise Time (±30%) |
300μs, 200V range, 100mA compliance. |
|||||||||
|
150V/μs, 20V range, 100mA compliance. |
||||||||||
|
DC Floating Voltage |
Output can be floated up to ±250VDC |
|||||||||
|
Remote Sense |
Up to 1V drop per load lead. |
|||||||||
|
Compliance Accuracy |
Add 0.3% of range and ±0.02% of reading to base specification. |
|||||||||
|
Range Change Overshoot 3 |
Adjacent range changes between 200mV, 2V and 20V ranges, 100mV typical. |
|||||||||
|
Minimum Compliance Value |
0.1% of range |
|||||||||
|
Command Processing Time 4 |
Autorange On:10ms.Autorange Off:7ms. |
|||||||||
|
Measurement |
Voltage |
Input Resistance |
>10 GΩ |
|||||||
|
Measurement Resolution |
1μV, ±200.000mV range |
|||||||||
|
10μV, ±2.00000V range |
||||||||||
|
100μV, ±20.0000V range |
||||||||||
|
1mV, ±200.000V range |
||||||||||
|
Measurement Accuracy |
±(0.012%+300μV), ±200.000mV range |
|||||||||
|
±(0.012%+300μV), ±2.00000V range |
||||||||||
|
±(0.015%+1.5mV), ±20.0000V range |
||||||||||
|
±(0.015%+10mV), ±200.000V range |
||||||||||
|
Temperature Coefficient |
±(0.15 × accuracy specification)/°C |
|||||||||
|
Current |
Voltage Burden (4-wire mode) |
< 1mV |
||||||||
|
Programmed Source Resolution |
10pA, ±1.00000μA range |
|||||||||
|
100pA, ±10.0000μA range |
||||||||||
|
1nA, ±100.000μA range |
||||||||||
|
10nA, ±1.00000mA range |
||||||||||
|
100nA, ±10.00000mA range |
||||||||||
|
1μA, ±100.000mA range |
||||||||||
|
10μA, ±1.00000A range |
||||||||||
|
Programmed Source Accuracy1 |
±(0.029%+300pA)), ±1.00000μA range |
|||||||||
|
±(0.027%+700pA), ±10.0000μA range |
||||||||||
|
±(0.025%+6nA), ±100.000uA range |
||||||||||
|
±(0.027%+60nA), ±1.00000mA range |
||||||||||
|
±(0.035%+600nA), ±10.00000mA range |
||||||||||
|
±(0.055%+6μA), ±100.000mA range |
||||||||||
|
±(0.22%+570μA), ±1.00000A range |
||||||||||
|
Temperature Coefficient |
±(0.1 × accuracy specification) / °C |
|||||||||
|
Resistance |
Range |
Resolution |
Test current |
Accuracy |
||||||
|
<2.00000Ω |
--- |
--- |
Source IACC+Meas.VACC |
|||||||
|
2.00000Ω |
10μΩ |
--- |
Source IACC+Meas.VACC |
|||||||
|
20.0000Ω |
100μΩ |
100mA |
±(0.1%+0.003 Ω), Normal |
|||||||
|
±(0.07%+0.001 Ω), Enhanced |
||||||||||
|
200.000Ω |
1mΩ |
10mA |
±(0.08%+0.03 Ω), Normal |
|||||||
|
±(0.05%+0.01 Ω), Enhanced |
||||||||||
|
2.00000kΩ |
10mΩ |
1mA |
±(0.07%+0.3 Ω), Normal |
|||||||
|
±(0.05%+0.1 Ω), Enhanced |
||||||||||
|
20.0000kΩ |
100mΩ |
100μA |
±(0.06%+3 Ω), Normal |
|||||||
|
±(0.04%+1 Ω), Enhanced |
||||||||||
|
200.000kΩ |
1Ω |
10μA |
±(0.07%+30 Ω), Normal |
|||||||
|
±(0.05%+10 Ω), Enhanced |
||||||||||
|
2.00000MΩ |
10Ω |
5μA |
±(0.11%+300 Ω), Normal |
|||||||
|
±(0.05%+100 Ω), Enhanced |
||||||||||
|
20.0000MΩ |
100Ω |
0.5μA |
±(0.11%+1k Ω), Normal |
|||||||
|
±(0.05%+500 Ω), Enhanced |
||||||||||
|
200.000MΩ |
1kΩ |
100nA |
±(0.66%+10k Ω), Normal |
|||||||
|
±(0.35%+5k Ω), Enhanced |
||||||||||
|
>200.000M Ω |
--- |
--- |
Source IACC+Meas.VACC |
|||||||
|
Temperature Coefficient |
±(0.15 × accuracy specification)/°C |
|||||||||
|
Source I mode, Manual OHMS |
Total uncertainty = I source accuracy + V measure accuracy (4-wire remote sense). |
|||||||||
|
Source V mode, Manual OHMS |
Total uncertainty = V source accuracy + I measure accuracy (4-wire remote sense). |
|||||||||
|
6-wire OHMS mode |
Available using active ohms guard and guard sense. Max. Guard Output Current: 50mA (except 1A range). Accuracy is load dependent. |
|||||||||
|
Guard Output Impedance |
<0.1Ω in ohms mode |
|||||||||
|
System Speed |
Maximum Range Change Rate |
75/second |
||||||||
|
Maximum Measure Auto Range Time |
40ms (fixed source) 6 |
|||||||||
|
Sequence reading rates7 (rdg./second) for 60Hz (50Hz) |
Speed |
NPLC/ Trig Origin |
Measure |
Source-Measure 9 |
||||||
|
TO MEM. |
TO GPIB |
TO MEM. |
TO GPIB |
|||||||
|
Fast |
0.01 / internal |
2081 (2030) |
1198 (1210) |
1551 (1515) |
1000 (900) |
|||||
|
488.2 |
0.01 / external |
1239 (1200) |
1079 (1050) |
1018 (990) |
916 (835) |
|||||
|
Medium |
0.1 / internal |
510 (433) |
509 (433) |
470 (405) |
470 (410) |
|||||
|
488.2 |
0.1 / external |
438 (380) |
438 (380) |
409 (360) |
409 (365) |
|||||
|
Normal |
1 / internal |
59 (49) |
59 (49) |
58 (48) |
58 (48) |
|||||
|
488.2 |
1 / external |
57 (48) |
57 (48) |
57 (48) |
57 (47) |
|||||
|
Speed |
NPLC/ Trig Origin |
Source-Measure Pass/Fail test 8,9 |
Measure Memory 9 |
|||||||
|
TO MEM. |
TO GPIB |
TO MEM. |
TO GPIB |
|||||||
|
Fast |
0.01 / internal |
902 (900) |
809 (840) |
165 (162) |
164 (162) |
|||||
|
488.2 |
0.01 / external |
830 (830) |
756 (780) |
163 (160) |
162 (160) |
|||||
|
Medium |
0.1 / internal |
389 (343) |
388 (343) |
133 (126) |
132 (126) |
|||||
|
488.2 |
0.1 / external |
374 (333) |
374 (333) |
131 (125) |
131 (125) |
|||||
|
Normal |
1 / internal |
56 (47) |
56 (47) |
44 (38) |
44 (38) |
|||||
|
488.2 |
1 / external |
56 (47) |
56 (47) |
44 (38) |
44 (38) |
|||||
|
Single Reading Operation Rates (rdg./second) for 60Hz (50Hz) |
Speed |
NPLC/ Trig Origin |
Measure |
Source-Measure 9 |
Source-Measure Pass/Fail test 8,9 |
|||||
|
TO GPIB |
TO GPIB |
TO GPIB |
||||||||
|
Fast(488.2) |
0.01 / internal |
256 (256) |
79 (83) |
79 (83) |
||||||
|
Medium(488.2) |
0.1 / internal |
167 (166) |
72 (70) |
69 (70) |
||||||
|
Normal(488.2) |
1 / internal |
49 (42) |
34 (31) |
35 (30) |
||||||
|
Component Interface Handler Time for 60Hz (50Hz):8, 10 |
Speed |
NPLC/ Trig Origin |
Measure |
Source Pass/Fail test |
Source-Measure Pass/Fail test 9,11 |
|||||
|
TO GPIB |
TO GPIB |
TO GPIB |
||||||||
|
Fast |
0.01 / internal |
1.04 ms (1.08 ms) |
0.5 ms (0.5 ms) |
4.82 ms (5.3 ms) |
||||||
|
Medium |
0.1 / internal |
2.55 ms (2.9 ms) |
0.5 ms (0.5 ms) |
6.27 ms (7.1 ms) |
||||||
|
Normal |
1 / internal |
17.53 ms (20.9 ms) |
0.5 ms (0.5 ms) |
21.31 ms (25.0 ms) |
||||||
|
System General |
Load Impedance |
Stable into 20,000pF typical |
||||||||
|
Differential mode Voltage |
250 VPk |
|||||||||
|
Common mode Voltage |
250 VDC |
|||||||||
|
Common mode Isolation |
>10GΩ, <1000pF |
|||||||||
|
Over Range |
105% of range, source and measure. |
|||||||||
|
Max. Voltage drop |
5V |
|||||||||
|
Max. Sense lead Resistance |
1MΩ |
|||||||||
|
Sense input Impedance |
>100G Ω |
|||||||||
|
Guard offset Voltage |
<150μV, typical |
|||||||||
|
Source output modes |
Fixed DC level, Memory List (mixed function), Stair (linear and log) |
|||||||||
|
Source memory list |
100 points max. |
|||||||||
|
Memory buffer |
5,000 readings @ 5 digits (two 2,500 point buffers). Includes selected measured value(s) and time stamp. Lithium battery backup(3 yr+ battery life). |
|||||||||
|
Programmability |
IEEE-488.2 (SCPI) |
|||||||||
|
5 user-definable power-up states plus factory default and *RST. |
||||||||||
|
Digital I/O Connector |
Active low input. |
|||||||||
|
Start of test, end of test, 3 category bits. |
||||||||||
|
+5V@ 300mA supply. |
||||||||||
|
1 trigger input, 4 TTL/Relay Drive outputs (33V @ 500mA, diode) |
||||||||||
|
Remote Interface |
USB/GPIB/LAN/RS-232 |
|||||||||
|
Insulation |
Chassis and Terminal |
20MΩ or above (DC 500V) |
||||||||
|
Chassis and AC cord |
30MΩ or above (DC 500V) |
|||||||||
|
Operation Environment |
Indoor use, Altitude: ≤ 2000m Ambient temperature: 0 ~ 40°C Relative humidity: ≤ 80% |
|||||||||
|
Installation category: II, Pollution degree: 2 |
||||||||||
|
Storage Environment |
Temperature: -20˚C ~ 70˚C |
|||||||||
|
Humidity: < 80% |
||||||||||
|
Input Power |
100-240VAC, 50-60Hz |
|||||||||
|
Power Consumption |
80W |
|||||||||
|
Accessories |
CD User manual x1, Quick Start manual x1 |
|||||||||
|
Test lead GTL-207A x 1, GTL-108A x 1, ALLIGATOR CLIP x 2 |
||||||||||
|
Dimensions |
214 (W) x 86 (H) x 356.5 (D) mm |
|||||||||
|
Weight |
Approx. 4.8kg |
|||||||||
